$100 shipped.
NOTE: Has some cosmetic scratches but otherwise gauranteed to work. Used in the NSX and then bought a ridiculously expensive $1000.00 amp so this will pay for tax :rollseyes:
May throw in some odds and end cables for low cost or free such as RCA, power etc.... from what I have left over. Let me know what you need.
Specs:
Number of Channels 4
Rated Power
continuous power 50W x 4 @ 4-Ohms RMS
100W x 4 @ 2-Ohms RMS
200W x 2 @ 4-Ohms bridged RMS
Total Power
total sum of 'rated power' 400 Watts
Bridgeable Yes
Crossover Controls High-Pass (HP): 40-400Hz 12dB/octave Butterworth
Low-Pass (LP): 40-400Hz 12dB/octave Butterworth
Tone Controls Bass: 0dB to +18dB @ 45Hz
Signal Input Low level: 2 RCA pair
Input switch: 2/4 ch.
Signal Output Low level: 1 RCA pair
Power Input Connector Block
Power Wire Gauge 4 AWG
Speaker Output Connector Screw terminal barrier strip
Speaker Wire Gauge 8 AWG to 18 AWG
Heat Sink Type Cast aluminum
Cooling Convection
Remote Controls Punch Bass EQ (included with cable)
Visual Indicators Power On
Signal Level
Thermal Status
Speaker Protection
Circuit Topology Class Class A/B
Frequency Response 20Hz to 20kHz +/- 0.5 dB
Shipping Weight 17.5 Lbs.
(7.9 Kg.)
Dimensions (HxWxL) 2.4 x 11 x 16.4 (in)
6.1 x 27.9 x 41.6 (cm)
50 watts RMS x 4 at 4 ohms (100 watts RMS x 4 at 2 ohms)
200 watts RMS x 2 at 4 ohms (4-ohm stable in bridged mode)
variable high-pass/low-pass crossover (40-400 Hz, 12 dB/octave)
variable Punch Bass boost (0-18 dB at 45 Hz) with remote
CEA-2006 compliant
Tri-way capable (Tri-Way crossover required)
8-gauge wiring kit and 60-amp fuse recommended — wiring and hardware not included with amplifier
MOSFET power supplies and output stages
MEHSA transfers heat efficiently from the MOSFET devices to the heat sink for high performance
TOPAZ eliminates ground loop noise
trans-ANA circuitry keeps preamp signal clean
NOMAD "intelligent" protection circuitry
preamp outputs
16-7/16"W x 2-3/4"H x 11-1/4"D
NOTE: Has some cosmetic scratches but otherwise gauranteed to work. Used in the NSX and then bought a ridiculously expensive $1000.00 amp so this will pay for tax :rollseyes:
May throw in some odds and end cables for low cost or free such as RCA, power etc.... from what I have left over. Let me know what you need.
Specs:
Number of Channels 4
Rated Power
continuous power 50W x 4 @ 4-Ohms RMS
100W x 4 @ 2-Ohms RMS
200W x 2 @ 4-Ohms bridged RMS
Total Power
total sum of 'rated power' 400 Watts
Bridgeable Yes
Crossover Controls High-Pass (HP): 40-400Hz 12dB/octave Butterworth
Low-Pass (LP): 40-400Hz 12dB/octave Butterworth
Tone Controls Bass: 0dB to +18dB @ 45Hz
Signal Input Low level: 2 RCA pair
Input switch: 2/4 ch.
Signal Output Low level: 1 RCA pair
Power Input Connector Block
Power Wire Gauge 4 AWG
Speaker Output Connector Screw terminal barrier strip
Speaker Wire Gauge 8 AWG to 18 AWG
Heat Sink Type Cast aluminum
Cooling Convection
Remote Controls Punch Bass EQ (included with cable)
Visual Indicators Power On
Signal Level
Thermal Status
Speaker Protection
Circuit Topology Class Class A/B
Frequency Response 20Hz to 20kHz +/- 0.5 dB
Shipping Weight 17.5 Lbs.
(7.9 Kg.)
Dimensions (HxWxL) 2.4 x 11 x 16.4 (in)
6.1 x 27.9 x 41.6 (cm)
50 watts RMS x 4 at 4 ohms (100 watts RMS x 4 at 2 ohms)
200 watts RMS x 2 at 4 ohms (4-ohm stable in bridged mode)
variable high-pass/low-pass crossover (40-400 Hz, 12 dB/octave)
variable Punch Bass boost (0-18 dB at 45 Hz) with remote
CEA-2006 compliant
Tri-way capable (Tri-Way crossover required)
8-gauge wiring kit and 60-amp fuse recommended — wiring and hardware not included with amplifier
MOSFET power supplies and output stages
MEHSA transfers heat efficiently from the MOSFET devices to the heat sink for high performance
TOPAZ eliminates ground loop noise
trans-ANA circuitry keeps preamp signal clean
NOMAD "intelligent" protection circuitry
preamp outputs
16-7/16"W x 2-3/4"H x 11-1/4"D
Attachments
Last edited:
