slipnby's NSx with iforged evo 18/19 check this out.
- Thread starter theWB
- Start date
When I was looking into iForged wheels, I was wondering how those would look on the NSX. Now I know! They look incredible! Good job!!
Z
Z
Very nice ! Congratulations !
Was it over cast that day? The first pic doesn't do much for them but the second is a little better. Maybe the flash wasn't on when the pics were taken. 
Although I bet in the sunlight in person they look very nice.
Although I bet in the sunlight in person they look very nice.
yummy!
looks hott!
looks hott!
The pics DO NOT do this car justice! I stopped by Mikes to see his new setup in person and man is it hot. Ben you did a 'sick' job,hope you take care of me as well as you did Mike. now all you need are some Tarox big brakes to finish the job! Mike the car is mean,nasty,sick and Evil....I love it! those that know me know I don't patronize,I needed a cold shower after viewing it 
sweet..................
Where in Miami? Havent seen but 1 other white around here
I took a ride today in mikes car with his new Iforge rims and tein ra coil overs,I viewed the setup a couple days ago but didnt get a ride until today. WB (Ben) did a great job of high speed balance and setting up the teins. the car felt very strong and stable in the twisty's (much better then my stock suspension and rims and better then I thought power wise with such large wheels,I think I am sold on the teins but still want lighter rims although mike wont need to worry to much about the big 18,19 combo slowing him down much after I install a custom nos setup on his car latter this week.the guy is pullin out all the stops.what I like about his car like 90 percent of most modded cars is it looks great with no 'RICE' factor.very tasteful upgrades.I cant state how much I like the teins....drool
Can someone tell me how deep the lips are front and back on this set-up?
Steve
Steve
car and rims look fabolous...
just from eye balling them they looked about 2 1/2 deep all around and very polished (shiny). he took more pics but they didnt come out right so I promised to take my camera over and get some decent shots and post them up.I will measure the deep lip at that timewhiteNSXs said:
- Joined
- 3 June 2003
- Messages
- 437
- Joined
- 3 June 2003
- Messages
- 437
- Joined
- 3 June 2003
- Messages
- 437
the front lip is 1.5 in and th rear is 3 in. they r set of for big brake which is coming after my custom nos kit from dave (bad carma).
mike
mike
Thanks Mike.slipnby said:
Do you happen to have close-up pictures of the wheels especially quarter views to show off the lips? I am also ordering a set of iforged and still trying to figure out sizes of lips to order. I will probably do 1.5 f and 2.5 r.
Steve
slipnby said:
Same sizes as mine.
WhiteNSX's, just curious, why 1.5/2.5?
Actually I don't like this kind of lips so I will try to get smaller lips. In this case I want a set of wheels that have clearances for the BBK. So I probably will do 1 inch front and 2 inches rear. The lips that I like are the ones on BBS wheels. The ones that have a "step-up" going towards the inside of the wheels. I thought your Flux wheels have deeper lips than these Evos and they don't clear the BBK.NSX FoYoAss said:
Steve
- Joined
- 3 June 2003
- Messages
- 437
white nsx mine is set up for big break kit. u can fit the brembo, but it is close, the ap and the tarok fit great
- Joined
- 3 June 2003
- Messages
- 437
they just have to do the offset to fit the big break kit 37 on front 40 on rear
Similar threads
