Miscellaneous NSX pins & screws question

[NsXMas]

My NSX needs some of the plastic push pins for the fender liners replaced. Where can we find cheap ones to replace the OEMs with? I remember Ethan from NSXclear telling me about a 100 pack for ~$20 or so online, so I'll post that info here when I hear back from him. But if you have other info on this, I'd be glad to hear it.

Also, I'm missing the screw for securing the NSX leather bra to the front. Where can I get replacement screws for that, and are they generic that I can find them at a hardware store?

Finally, one of the engine cover screws holding the rod that props the cover open is missing. Where can I get one of these too? Are they generic enough that I can find one at a hardware store?

Thanks in advance for any help.

 

[nsxter]

I can't help with the fender liner clips, but the bra screws are a special type. Just but the oem ones part number 08P35-SL0-200R1 They are pretty inexpensive (about 5 bucks). I probably have a few oem fender liner clips how many do you need?

 

[NsXMas]

Thanks Don! I think I need about 6-7 fender clips. If you have extras that would be great.

I'll order a bunch from the web when I find out which ones are good and pay you back in the future. :smile:

 

[nsxter]

I'll dig around and see how many I have....:smile:

 

[NSXclear]

http://www.thefastenerwarehouse.com/page/page/568361.htm

It's TR 126 or TR 126B.

 

[Osiris_x11]

me needs a few of these too...

http://www.thefastenerwarehouse.com/page/page/568361.htm

It's TR 126 or TR 126B.

Thanks! Any idea what their S/H is like? (requires registering to get final price, I think? Or S/H is flat $4.95 for all orders <$99?)... in-case I should opt for the 100 pack instead of 25 (minimum order has to be $10).

Are any from the following page more relevant (just curious)? Fasterner Warehouse: Honda Trim Retainers

In the past, I've seen the few ongoing threads here on Prime w/ regards to fender-liner clips, but I can't recall the sizes (ie. diameter & length).

 

[NSXclear]

Yes, the shipping should be only $4.95. He ships them using the flat rate USPS small box.

These clips are a little different to the OEM style. The OEM clips, you push in the center of the clips slightly, then remove the base. These aftermarket clips you have to use a small pick to pull up on the center to remove them.

But they do fit well and work the same.

There are some other clips on the market that are more similar to the OEM version, but they are more expensive. I figured that I would go with the cheaper clips cause no one is going to see them, and I was replacing most of the clips anyways.

 

[Osiris_x11]

Yes, the shipping should be only $4.95. He ships them using the flat rate USPS small box.

These clips are a little different to the OEM style. The OEM clips, you push in the center of the clips slightly, then remove the base. These aftermarket clips you have to use a small pick to pull up on the center to remove them.

But they do fit well and work the same.

There are some other clips on the market that are more similar to the OEM version, but they are more expensive. I figured that I would go with the cheaper clips cause no one is going to see them, and I was replacing most of the clips anyways.

Thanks buddy. All I needed to know/here. I'll just grab a big package & replace the few missing and/or damaged ones I have, keep a bunch as spares & offer them to locals. I do have a handful of OEM/stock ones in original packaging which I wish to keep for future reference (not to mention how cost-prohibitive they tend to be, jeez...)!

Side-note, does anyone have the precise measurements/specs for the OEM/stock fender-liner clips (as-in the actual hole size, clip-head diameter, clip-stem length, etc)? While perusing, I often see incredibly inexpensive bulk offerings of various bumper & fender clips that only have specs/sizes listed, not actual detailed application or cross-listed P/N's (ie. "Honda body / bumper / fender clips").

 

[warrenw]

Thanks buddy. All I needed to know/here. I'll just grab a big package & replace the few missing and/or damaged ones I have, keep a bunch as spares & offer them to locals. I do have a handful of OEM/stock ones in original packaging which I wish to keep for future reference (not to mention how cost-prohibitive they tend to be, jeez...)!

Side-note, does anyone have the precise measurements/specs for the OEM/stock fender-liner clips (as-in the actual hole size, clip-head diameter, clip-stem length, etc)? While perusing, I often see incredibly inexpensive bulk offerings of various bumper & fender clips that only have specs/sizes listed, not actual detailed application or cross-listed P/N's (ie. "Honda body / bumper / fender clips").

Everyone that owns an NSX should have a box of AUVECO 16782 8mm Hole, 20mm Flange Dia. push type retainers.. I bought mine on ebay for $5.00 for a box of 25...
see: http://www.nsxprime.com/forums/showthread.php?t=116010

 

[Osiris_x11]

let the hoarding begin...

Everyone that owns an NSX should have a box of AUVECO 16782 8mm Hole, 20mm Flange Dia. push type retainers.. I bought mine on ebay for $5.00 for a box of 25...
see: http://www.nsxprime.com/forums/showthread.php?t=116010

Thanks for the spec's. Gonna keep an eye on ebay & Amazon, as well as other generic/no-name clip & fastener distributing vendors.

For posterity's sake, the NSX fender-liner clip spec's:

OEM/stock P/N: 91545-SEO-003
Head Diameter: 20mm
Stem Length: 14mm
Fits into 8mm Hole

Now, only if I can find more economically priced speed-nut clips & applicable bolts to fasten the OEM/stock lip to the front bumper lower-valance (the replacement cost for genuine OEM/stock speed-nut clip & bolt hardware is nose-bleed inducing)! Grrr...