Aftermarket Seats
- Thread starter wildrice
- Start date
I want seats also.i just have some other mods to finish first. my momo wheel and a hub that fits to use the factory loom.then my nos and straight pipes.BUT back to your seat mounting issue.have you looked on cris's site.he sells recargos with the taitec mounting brackets sliders (side slider for recargo)he has tested them with other regargos and I believe so has mark at dali.i bet the taitecs will work with your seat.cris gives the spec on the seats that inticate if they should work.he states that he has only tested certain seats so just cuase its from the same vendor does not mean they will all work. but the taitec and sparco torinio is plug and play and the regargo sport seat.has to be a certain number I dont fully understand but go here and look if you havnt already:
http://scienceofspeed.com/products/interior_performance_products/Recaro/
cris is very good about answering ? about fitment
I also believe the same factory makes the japanese mounts for taitec and mugen but as always this is from memory.. take with grain of salt. hope this was a help.I want momos and am trying to find if i can use them with the taitec mounts.if you have any info on the mugen mounts please email me
best regards david
ps you most likely have already done your homework and been to sos and dali but just wan to help if i could
cris jump in here and correct me if i am giving out bad info about your product fitment OH YEAH if you go with the taitec monts sliders i think thats all you need with the seat and also think it was indicated it would give you more head room not less!sorry for the bad spelling its late
[This message has been edited by BadCarma (edited 02 July 2002).]
http://scienceofspeed.com/products/interior_performance_products/Recaro/
cris is very good about answering ? about fitment
I also believe the same factory makes the japanese mounts for taitec and mugen but as always this is from memory.. take with grain of salt. hope this was a help.I want momos and am trying to find if i can use them with the taitec mounts.if you have any info on the mugen mounts please email me
best regards david
ps you most likely have already done your homework and been to sos and dali but just wan to help if i could
cris jump in here and correct me if i am giving out bad info about your product fitment OH YEAH if you go with the taitec monts sliders i think thats all you need with the seat and also think it was indicated it would give you more head room not less!sorry for the bad spelling its late
[This message has been edited by BadCarma (edited 02 July 2002).]
info on seats that fit the side slider:
The TAITEC Side Mount Sliding Seat Rails utilize factory mounting locations for a plug-and-play installation, and do not require drilling.
These seat rails are one of the lowest sitting rail designs available for the NSX.
Any side-mount seats that fit in the NSX may be used with the TAITEC Sliding Seat Rails. However, only seats with side mount widths of less than 279 will fit between the rails for maximum height reduction. Many will fit, however, we can not guarantee that seats other than the ones below that we have tested will fit. Seats known to fit:
Sparco REV
Recaro SPG
The TAITEC Side Mount Sliding Seat Rails utilize factory mounting locations for a plug-and-play installation, and do not require drilling.
These seat rails are one of the lowest sitting rail designs available for the NSX.
Any side-mount seats that fit in the NSX may be used with the TAITEC Sliding Seat Rails. However, only seats with side mount widths of less than 279 will fit between the rails for maximum height reduction. Many will fit, however, we can not guarantee that seats other than the ones below that we have tested will fit. Seats known to fit:
Sparco REV
Recaro SPG
heres the info on the bottom mounted seats.as you can see from the two posts some seats even made by same vendor recargo, sparco need different mounts some bottom sliders some side..heres the rest:
Until now, there was not a reasonable and reliable performance seat mounting solution available in the United States for the NSX. Hand-built in Japan especially for the NSX, the TAITEC Bottom Mount Sliding Seat Rails are designed to mount bottom mounting seats such as the Sparco Torino.
TAITEC Bottom Mount Seat Rail with mounting brackets
The TAITEC Bottom Mount Sliding Seat Rails utilize factory mounting locations for a plug-and-play installation, and do not require drilling.
Seats with bottom seat mounts are typically for street use and reclinable. Seats such as the Sparco Torino are compatible with these rails. Seats must have a 4 hole bottom mount dimensions of 275 x 345. Not for use with side mount seats. TAITEC Side Mount Sliding Seat Rails available here.(sos site)
Contact ScienceofSpeed for special seat/rail discounted purchases. ScienceofSpeed is an authorized vendor for Recaro, Sparco and OMP.
TAITEC Bottom Mount Sliding Seat Rails include:
bottom mount sliding seat rails for the NSX
mounting hardware
side seat belt anchors (may be used to mount the factory seat belts)
David
Until now, there was not a reasonable and reliable performance seat mounting solution available in the United States for the NSX. Hand-built in Japan especially for the NSX, the TAITEC Bottom Mount Sliding Seat Rails are designed to mount bottom mounting seats such as the Sparco Torino.
TAITEC Bottom Mount Seat Rail with mounting brackets
The TAITEC Bottom Mount Sliding Seat Rails utilize factory mounting locations for a plug-and-play installation, and do not require drilling.
Seats with bottom seat mounts are typically for street use and reclinable. Seats such as the Sparco Torino are compatible with these rails. Seats must have a 4 hole bottom mount dimensions of 275 x 345. Not for use with side mount seats. TAITEC Side Mount Sliding Seat Rails available here.(sos site)
Contact ScienceofSpeed for special seat/rail discounted purchases. ScienceofSpeed is an authorized vendor for Recaro, Sparco and OMP.
TAITEC Bottom Mount Sliding Seat Rails include:
bottom mount sliding seat rails for the NSX
mounting hardware
side seat belt anchors (may be used to mount the factory seat belts)
David
pole position DALI site http://www.daliracing.com/v666-5/catalog/furniture/recaro_seat.cfm
there is a pic on the site showing the pole positions mounted in the nsx....sweet look:
http://www.daliracing.com/v666-5/catalog/furniture/more_recaro_001.cfm
[This message has been edited by BadCarma (edited 02 July 2002).]
there is a pic on the site showing the pole positions mounted in the nsx....sweet look:
http://www.daliracing.com/v666-5/catalog/furniture/more_recaro_001.cfm
[This message has been edited by BadCarma (edited 02 July 2002).]
Similar threads
