NSX NC1 new front frame

Procar Specials · 19 January 2020

Thats the actual status of your new project.
We removed the complete aluminium front section, because some of these parts were damaged during a smaller impact.

Its no good idea that the preowner drove at rain with that condition of rear tires.

Procar Specials · 19 January 2020

Its very interesting how Honda did attach that support frame.

Nice progress from our side, because we got a complete intact support frame.

Quite sure that these pictures are very rare.

hondasash · 20 January 2020

Looks like there is pretty much work to do before this car drivers on offical roads again.

Procar Specials · 20 January 2020

Thats right, but so we can learn very much about that car and the concept.
We are able to work onto that car into the future and offer some Service works.

We have to strip the interior too because of some issues like SRS unit and airbags etc.
After this is done, we start to work on the rear end, remove the rear bumper for another exhaust and intake system.

Maybe we also take the engine out to check more details.

Honcho · 21 January 2020

What an interesting project! Cool to see the frame exposed. I was under the impression that any damaged NC1 had to be repaired at the PMC only, due to the specialized equipment they have there.

Procar Specials · 22 January 2020

Yes, it is.
Till now all is perfect.

I have noticed that the weldings at the front frame are not really nice regarding the aspect that this is a 200000 USD car.

Sure that our WIG specialist can do it better.

Procar Specials · 22 January 2020

The new front support frame is prepared for installation.
All weldings are removed.

Installation is a straight forward job, because there is 1 mounting hole at each of the middle frame.
If these both screws will fit, all is perfect.

Than we have a special measurement tool for the upper frames, so no reason to send the car back to USA.

Procar Specials · 5 February 2020

Next few steps are done, the new front support frame fits perfect.

Procar Specials · 5 February 2020

All fits perfect now.
Next step is the paint job and installation of the skeletons

Procar Specials · 5 February 2020

Even that project is very time consuming, still some fun to prepare my NA2R with new cf parts

Procar Specials · 9 February 2020

some nice progress and pictures from our work with the NC1

Procar Specials · 17 February 2020

some more rare photos.
This is how a NC1 seat looks behind the leather
Leather has poor quality, but can be repaired.

Procar Specials · 17 February 2020

some of the SRS sensors….there are many .-))

Procar Specials · 17 February 2020

Airbag section installed properly.

Procar Specials · 17 February 2020

Th front cf splitter has poor Quality...…
4800 USD for a part made in China, thats awesome

signalpuke · 17 February 2020

goldNSX · 17 February 2020

The Corona virus will reveal in a few months who's manufacturing what and how much in China.

Procar Specials · 17 February 2020

Had the same thoughts about that…..we will see. :smile:

Finally the NC1 looks naked, but completed now.
Ready to install the hood, the fenders and the front bumper (3pcs)

Very complex, but logical.
Its fascinating, how many parts Honda designed and fitted between the front frame, no comparsion to our old version.
Thumps up for that , even the build quality is far away from being perfect.

Procar Specials · 1 May 2020

Done

Picture remembers me at another picture

drmanny3 · 1 May 2020

Remarkably well done. You have learned a lot about the car that should help everyone in the future. Don't forget to add up all your time as well as parts. Thank you for sharing.

lucky · 8 May 2020

looks sweet - nice restoration/repair!

dc1edh · 8 May 2020

Congrats on the restoration! That’s not an easy feat. You should be very proud!

drmanny3 · 6 July 2020

Curious how in Europe cars suffering significant damaged are titled. Was this car totaled? Does the accident show up in reports? Do you have to requalify the car in some fashion? Good job, looks like it was put back together correctly.Regards.

Procar Specials · 10 October 2020

New part for a customer in columbia. (Rebadge)
Like that idea.

Box shows Mexiko on the partno badge, the part himself has a sticker with Takata AG in Aschaffenburg/Germany

BrakeExpert · 17 September 2022

Typical Honda am I right?

At least this front frame piece is basic enough that in the future it could be replicated with relative ease, opposed to say a back quarter panel of an NA1. This helps tremendoulsly for longevity if you ask me

NSX NC1 new front frame

Similar threads