MODERN NSX Interior / Exterior LED Lighting for your NSX: Part II

Blue Batmobile said:

Rick! do you offer any kind of sequential turnsignal kit for the NSX ?

B@t

Click to expand...

s4play said:

Are you talking about like the new Mustang tails? Yes we offer a few sequential turn signal options in both red and amber :biggrin:

Did you want this integrated into your OEM bumper lenses? I would need your lenses to do the modifications. And since this is a custom job we can change which bulbs are your parking and which one blinks, etc.

Drop us an email and we can discuss further:

[email protected]


rick

Click to expand...

s4play said:

Decided to start a new thread since the last one had too much outdated info and pictures so please read this thread thoroughly and PM us if you have any questions.

We now offer bundled kits for your NSX no matter what year you drive!

See below for some of our most popular kits but if you have a custom requirement – don’t hesitate to email us ([email protected])

a) Interior NSX Dome light kit $60.00
b) License Plate LED Kit $30
c) Sidemarkers $30

For other lights, please contact us and we’ll be happy to send you a quote SAME DAY! :biggrin:

As with any technology, LED’s are the way to go these days since not only does it look cooler but you have an added benefit of drawing MUCH less power and heat.

Owners have noticed not only a brighter pure white light (5000k) but if you forget to close your doors or trunk, these lights will not kill the battery. He left the lights on for an entire weekend and the car started right up!

Shipping/processing in lower 48 states is a flat $10.00

Our Paypal is:

[email protected]

Orders received will usually ship NEXT DAY!


Visit our website too: www.euroboutique.us

Thanks!


Samples of our lights in action:

Click to expand...

Blue Batmobile said:

Yes, I would like my stock rear tails to have sequential turns .

B@t

Click to expand...

HIJACKER said:

I still want to see a way to update the OEM cluster lighting and center console lighting to be more "modern". ESPECIALLY the gauges. The silver rings and CF replacement bezel looks nice, but the orange glow is just so "90's"

Click to expand...

s4play said:

Is the NSX dash backlit by standard filament bulbs? I have never torn one apart but if is similar in design to the s2000, then it might work.

I know there is an s2000 vendor who has build this full LED replacement kit and we've installed quite a few for clients. I think the NSX is a much smaller audience in terms of people who would buy it so this may be tricky.

Probably should start a separate thread since this is primarily for our Interior and Exterior bulb conversion which is plug and play. We do offer load resistors for the blinkers too!


thanks

Click to expand...

scammy said:

Hey Rick
Installed my interiors, way better thanks mate.
The rest of the rear tail light bulbs are of the old filament push in and turn variety(bayonet?) do you have any options for those?
Cheers

Click to expand...

s4play said:

We also sell load resistors and offer custom installation services if you are local to the SF Bay Area!

Both owners have NSX's so we know this car well.

Click to expand...

luigib said:

Which lights that you sell require load resistors? You mentioned the front signals do?

Click to expand...

Sleek said:

I had Rick build a 4 led light bar in my front marker light and had him switch the turn signal to the outside of the lens using the amber park light as the turn signal and the 4 led bar in the front larger section of the lens. To get the amber park lights to work as the turn signal I needed to add one 6 ohm resistor to each side. If you don't you'll have a hyper flash ( quick flashing of the turn signal ), the resistor more or less tells the car that it's getting enough power for the difference in power between the normal big clear turn signal and the amber park light to act as the turn signal.

Click to expand...